Blade Fits
How to Sharpen Your Reel Lawn Mower – Part Two: Sharpening the Blades
Once you have determined that your blades do need sharpening, there are several way you can accomplish this. Whichever method you choose will depend on your personal preference. If you have lots of good arm strength and your mower is pretty clean go with the One Wheel Off Method. If your mower is dirty, use the Two Wheels Off Method so you can clean the parts and re-grease the reel shaft. If you aren’t physically very strong, you may wish to try the Push Sharpening Method. And finally, if you have drill and socket bit set you may wish to give the Drill Bit Method a go.
One Wheel Off Method
If you have chosen to remove just one wheel, keep the pawl in place. You may wish to flip the mower over to its upright position or you can continue with it upside down, or even on its side. I prefer to flip is over to right-side up as it makes more sense to me.
Fit the sharpening crank over the shaft and pawl. Insert one of your pieces of paper between the blade and the knife blade at one end of the reel and turn the crank so the reel is moving forward, the same way it would be moving if you were mowing the lawn. You will want to continue the turning until all of the blades have had a chance to pass over the piece of paper so you can see if they are all cutting the paper smoothly. Repeat with more pieces of paper in the middle of the reel and then again on the opposite side that you started from. If the blades are not cutting the paper cleanly and easily all the way around then they need sharpening.
Apply the lapping compound to the cutting edges of the blades. Apply sparingly or it tends to run off the cutting edge, but ensure all cutting surfaces are well covered. Apply to all blades, turning the crank to turn the reel as needed to expose all of the blade. This time you will be turning the reel backwards, or the opposite way from the way it would turn if you were mowing.
Once all the cutting surfaces have been covered with lapping compound, turn the crank to turn the reel backwards for about 7-8 minutes. In some cases, the lapping compound will begin to change colour. You want to see that the cutting edge is bright and shiny with a smooth edge. This is hard work! Take breaks, Tom Sawyer your children into helping, or try using a drill bit (more below) to turn the reel.
Once you think the blades are sharp, repeat the paper test to ensure all cutting surfaces are sharp. If the paper is cut cleanly and easily then you are finished. Adjust the blades if needed.
Replace the gear, the wheel, the E ring (this will be harder to get back in than it was to pry off) and the side cover.
Two Wheels Off Method
With the mower upside down, remove the wheel cover, E ring, gear and pawl from the second side. Keep the pawl in place on the first wheel. Flip the mower over so it is right side up. Clean out any dirt as needed.
Fit the sharpening crank over the shaft and pawl. Insert one of your pieces of paper between the blade and the knife blade at one end of the reel and turn the crank so the reel is moving forward, the same way it would be moving if you were mowing the lawn. You will want to continue the turning until all of the blades have had a chance to pass over the piece of paper so you can see if they are all cutting the paper smoothly.Repeat with more pieces of paper in the middle of the reel and then again on the opposite side that you started from. If the blades are not cutting the paper cleanly and easily all the way around then they need sharpening.
Apply the lapping compound to the cutting edges of the blades. Apply sparingly or it tends to run off the cutting edge, but ensure all cutting surfaces are covered. Apply to all blades, turning the crank to turn the reel as needed to expose all of the blade. This time you will be turning the reel backwards, or the opposite way from the way it would turn if you were mowing.
Once all the cutting surfaces have been covered with lapping compound, turn the crank to turn the reel backwards for about 7-8 minutes. In some cases, the lapping compound will begin to change colour. You want to see that the cutting edge is bright and shiny with a smooth edge. This is hard work! Take breaks, Tom Sawyer your children into helping, or try using a drill bit (more below) to turn the reel.
Once you think the blades are sharp, repeat the paper test to ensure all cutting surfaces are sharp. If the paper is cut cleanly and easily then you are finished.
Adjust the blades if needed. Replace the gear, the wheel, the E ring (this will be harder to get back in than it was to pry off) and the side cover for one wheel then repeat for the second wheel.
Push Method
This method initially seems more complicated, but once we experienced the hard work of arm sharpening, the ease of push sharpening seems to far outweigh the slightly longer disassembly and reassembly time.
With the mower upside down, remove the wheel cover, E ring, gear and pawl from the second side. Keep the pawl in place on the first wheel. Flip the mower over so it is right side up. Clean out any dirt as needed.Fit the sharpening crank over the shaft and pawl. Insert one of your pieces of paper between the blade and the knife blade at one end of the reel and turn the crank so the reel is moving forward, the same way it would be moving if you were mowing the lawn. You will want to continue the turning until all of the blades have had a chance to pass over the piece of paper so you can see if they are all cutting the paper smoothly.
Repeat with more pieces of paper in the middle of the reel and then again on the opposite side that you started from. If the blades are not cutting the paper cleanly and easily all the way around then they need sharpening.We have not tried this method ourselves but came across it while reading reviews. His suggestion “Remove both wheels , remove and switch ratchet gears from L to R and vice versa, flip over pawls, apply compound and push the mower backwards for about 5 minutes”. From reading this we assume he means to put the left gear and pawl on the right side of the reel shaft and vice versa. We also assume that you would need to replace the wheels to push it backwards.
Once you think the blades are sharp, you would then need to disassemble the wheels, repeat the paper test to ensure all cutting surfaces are sharp. If the paper is cut cleanly and easily then you are finished. Adjust the blades if needed. Switch the gears and pawls back to their original sides and then replace the wheels. We will update you if we try this method to let you know how it works. I think that once it was done once, it wouldn’t seem as confusing and would be a lot easier than cranking by hand.
Drill Bit Method
There were many mentions of turning the reel with a drill. You will need to find a socket attachment that fits over the reel shaft, a 16 or 17 mm socket size were mentioned most often. We would recommend removing the pawl as it might fly out while the drill is turning the shaft. Follow the instructions for disassembly as for the One or Two Wheel method. If you removed both gears, we recommend you remove both pawls. Fit the socket over the reel shaft and let the drill do the work for you. No one seems to mention how long to do this but we imagine it would take far less time than by hand. Visually check your blades for sharpness after 3 or 4 minutes. Re-assemble the wheel(s) as for other methods.
That’s it! It may seem complicated at but after the first time you will be a pro! If you are not sure if your blades need to be sharpened please see Part One of our series, How to Sharpen Your Reel Lawn Mower – Part One: When Should Your Blades Be Sharpened?
About the Author
Teresa is an avid, eco-conscious, gadget-loving gardener who herself owns two reel lawn mowers. Visit www.bestreellawnmowerreviews.com for reviews of the most popular makes and models based on owners’ comments as well as field tests and editorial reviews.
|
|
FM19; 12pc 4BIM 4Japan 4Wd Oscillating MultiTool Saw Blade fits Fein Multimaster $0.98 |
|
|
FM16; 10pc: 8Wood 2Wide Oscillating MultiTool Saw Blades fits Fein Multimaster $0.98 |
|
|
FM13; 10pc: 2Japan 8Wood Oscillating MultiTool Saw Blades fits Fein Multimaster $0.98 |
|
|
FM10; 10pc: 8Japan 2Wood Oscillating MultiTool Saw Blades fits Fein Multimaster $0.98 |
|
|
FM1; 10pc: 2Japan 8BiMetal Oscillating MultiTool Saw Blade fits Fein Multimaster $0.98 |
|
|
FM7; 10pc: 2Japan 8Wide Oscillating MultiTool Saw Blades fits Fein Multimaster $0.98 |
|
|
FM24; 4pc: Japan Oscillating MultiTool Saw Blade fits Fein Multimaster $0.98 |
|
|
FM18; 10pc:4BIM 3Wood 3Rnd Oscillating MultiTool Saw Blade fit Fein Multimaster $0.98 |
|
|
FM15; 10pc: Wood Oscillating MultiTool Saw Blades fits Fein Multimaster $0.98 |
|
|
FM21; 13pc:4BIM 4Wood 5Scraper Oscillating Tool Saw Blades fits Fein Multimaster $0.98 |
|
|
FM12; 10pc:8Japan, 2Wide Oscillating Multi Tool Saw Blades fits Fein Multimaster $0.98 |
|
|
FM9; 10pc: 2BIM 8Japan Oscillating MultiTool Saw Blade fits Fein Multimaster $0.98 |
|
|
FM6; 10pc: 2Metal, 8Wide Oscillating Multi Tool Saw Blades fit Fein Multimaster $0.98 |
|
|
FM3; 10pc:8Bi-Metal, 2Wide Oscillating MultiTool Saw Blade fits Fein Multimaster $0.98 |
|
|
FM23; 4pc: Bi-Metal Oscillating MultiTool Saw Blades fits Fein Multimaster $0.98 |
|
|
FM20;11pc 4BIM 3Wood 3Wide 1Rnd Oscillating Tool Saw Blade fits Fein MultiMaster $0.98 |
|
|
FM14; 10pc: 2BIM, 8Wood Oscillating MultiTool Saw Blade fits Fein Multimaster $0.98 |
|
|
FM17; 10pc: 4BIM 4Japan 2R Oscillating MultiTool Saw Blade fits Fein Multimaster $0.98 |
|
|
FM8; 10pc: Wide Oscillating MultiTool Saw Blades fits Fein Multimaster $0.98 |
|
|
FM5; 10pc: 2Bi-Metal 8Wide Oscillating MultiTool Saw Blade fits Fein Multimaster $0.98 |
|
|
FM11; 10pc: Japan Oscillating MultiTool Saw Blades fits Fein Multimaster $0.98 |
|
|
Circular HSS Oscillating Uni-Fit Tool Blade for Fein Multimaster, Mastercraft,++ $0.99 |
|
|
Fitzall 2.5″ Wide UNIVERSAL Oscillating Multi Tool Blades fits Dremel Multimax $0.99 |
|
|
DISSTON RECIPROCATING BLADES 4″ 1/2″ SHANK FITS ALL SAWS CARBIDE MED. GRIT 2 CT. $0.99 |
|
|
Circular HSS Oscillating Uni-Fit Tool Blade for Fein Multimaster, Mastercraft,++ $0.99 |
|
|
Fitzall 30mm SS ‘UNIVERSAL Multi Oscillating Tool Blades fits Ridged Jobmax $0.99 |
|
|
Oscillating Multi Blade Kit Fits Rockwell Sonicrafter $0.99 |
|
|
Circular HSS Oscillating Uni-Fit Tool Blade for Fein Multimaster, Mastercraft,++ $0.99 |
|
|
10″ Oregon Chainsaw Blade. Fits on Craftsman, Poulan, Remington. New in package. $0.99 |
|
|
New Oregon Chainsaw blade. 14″ Fits Homelite, McCulloch, Remington, Stihl. New $0.99 |
|
|
3 3″ Semi Round BiMetal Oscillating Multi Tool Saw Blades fits Fein Multimaster $0.99 |
|
|
Nail Eater BI-Metal UNIVERSAL Oscillating Multi Tool Blades fits Ridged Jobmax $0.99 |
|
|
Fitzall 20mm SS UNIVERSAL Oscillating Multi Tool Blades fits Ridged Jobmax $0.99 |
|
|
Fitzall 10mm SS UNIVERSAL Oscillating Multi Tool Blades fits Ridged Jobmax $0.99 |
|
|
Fitzall Flush Scraper UNIVERSAL Oscilating MultiTool Blades fits Dremel Multimax $0.99 |
|
|
Circular HSS Oscillating Uni-Fit Tool Blade for Fein Multimaster, Mastercraft,++ $0.99 |
|
|
Fitzall 30mm SS ‘UNIVERSAL Multi Oscillating Tool Blades fits Craftsman Nextec $0.99 |
|
|
Fitzall 20mm SS UNIVERSAL Oscillating Multi Tool Blades fits Craftsman Nextec $0.99 |
|
|
Fitzall 10mm SS UNIVERSAL Oscillating Multi Tool Blades fits Craftsman Nextec $0.99 |
|
|
Brazed Carbide Grout UNIVERSAL Oscillating Multi Tool Blades fits Ridged Jobmax $0.99 |
|
|
Circular HSS Oscillating Uni-Fit Tool Blade for Fein Multimaster, Mastercraft,++ $0.99 |
|
|
Fitzall 2.5″ Wide UNIVERSAL Oscillating Multi Tool Blades fits Ridged Jobmax $0.99 |
|
|
Multi Blades Fit Rockwell Sonicrafter Oscillating Saw $0.99 |
|
|
Circular HSS Oscillating Uni-Fit Tool Blade for Fein Multimaster, Mastercraft,++ $0.99 |
|
|
HK 500 TT tail case W/ carbon tail blades,also fits, ALIGN TREX 500, & Copter X $0.99 |
|
|
Circular HSS Oscillating Uni-Fit Tool Blade for Fein Multimaster, Mastercraft,++ $0.99 |
|
|
Fits Atra Plus Razor blades Cartridges Refill Handle Shaver 1pcs $0.99 |
|
|
76 BOSCH ASSORTED JIGSAW BLADES Fits CRAFTSMAN JIG SAW $0.99 |
|
|
W126 Mercedes Wiper Blade Intermittent Wiper Relay, 380SE – Fits Many 0008210863 $0.99 |
|
|
W126 Mercedes Fan Blade & Fan Clutch off 380SE Fits Many Models $0.99 |
|
|
Fitzall Half Moon UNIVERSAL Oscillating Multi Tool Blades fits Ridged Jobmax $0.99 |
|
|
Fitzall Specialty UNIVERSAL Oscillating Multi Tool Blades fits Ridged Jobmax $0.99 |
|
|
Fits Atra Plus Razor blades Cartridges Refill Handle Shaver 1pcs $0.99 |
|
|
55-460-1 PolyCut Blade fits Stihl 4111-007-1001 $1.00 |
|
|
BATTERY FIT Samsung SPH-A900, SPH-A900M, Blade,MM-A900 $1.00 |
|
|
’18 UNIVERSAL FIT WIPER BLADES. SAVE MONEY !! $1.00 |
|
|
16′ UNIVERSAL FIT WIPER BLADES $1.00 |
|
|
‘ 22 UNIVERSAL FIT WIPER BLADES $1.00 |
|
|
FISKARS / Fits OLFA 60 mm Replacement Blades 5 packs of 5 = 25 Blades Total NEW $1.04 |
|
|
PET Grooming ANDIS CERAMICEDGE A5 Ceramic 1/4″Blade 5FC 5F*Fit Oster Clippers NR $1.25 |
|
|
Trimmer Edger blade universal fit 9″ x 1 1/2″ new $1.49 |
|
|
13504-103-1026, FITS TRITON BLADES, BLADE BOLT $1.58 |
|
|
Fitzall Half Moon UNIVERSAL Oscillating Multi Tool Blades fits Craftsman Nextec $1.61 |
|
|
BLADE SPACER FITS FLYMO POWER COMPACT 330, 400 $1.66 |
|
|
40-141 Edger Blade fits Stihl Echo Shindaiwa 1″ ID 8″ L $1.69 |
|
|
PLASTIC BLADE FITS FLYMO MINIMO E25 E30 DUO E400 PK 6 $1.71 |
|
|
Fitzall Specialty UNIVERSAL Oscillating Multi Tool Blades fits Dremel Multimax $1.76 |
|
|
Craftsman 12″ Carbide Grit Saw Blade, Fits Hacksaw Frame $1.79 |
|
|
5 Spare Blades to fit all 18mm snap off Knives $1.98 |
|
|
2 TRICO WINSHEILD WIPER BLADES 20-1 (I DONT WHAT CARS THEY FIT) $1.99 |
|
|
TWO 28 INCH PREMIUM WIPER BLADES FITS MOST MAKES AND MODELS $1.99 |
|
|
TWO 28 INCH PREMIUM WIPER BLADES FITS MOST MAKES AND MODELS $1.99 |
|
|
TWO 28 INCH PREMIUM WIPER BLADES FITS MOST MAKES AND MODELS $1.99 |
|
|
TWO 26 INCH UNI POINT WIPER BLADES FITS MOST MAKES AND MODELS $1.99 |
|
|
TWO 26 INCH UNI POINT WIPER BLADES FITS MOST MAKES AND MODELS $1.99 |
|
|
TWO 23 INCH PREMIUM WIPER BLADES FITS MOST MAKES AND MODELS $1.99 |
|
|
TWO 23 INCH PREMIUM WIPER BLADES FITS MOST MAKES AND MODELS $1.99 |
|
|
FORCE Upper Main Blade Set (1 pair): MH-35/FHX Fits Blade MCX EFLH2221 FCE2021 $1.99 |
|
|
Vintage X-Acto Refill Blades No. 1 Asst. 5Pcs Fits Hdle # 1,3,7 $1.99 |
|
|
5pk Carton Cutter Blades Refill Fits Most RKB5 $1.99 |
|
|
NEW OEM GENUINE HUSQVARNA BLADE NUT#503856301 FITS TRIMMERS $2.00 |
|
|
GILLETTE VECTOR PLUS RAZOR FITS CONTOUR ATRA BLADES $2.08 |
|
|
Nail Eater BI-Metal UNIVERSAL Oscillating Multi Tool Blades fits Ridged Jobmax $2.25 |
|
|
PLANE BLADE FITS – STANLEY 18 – RECORD 018 VERY GOOD CONDITION (E) $2.37 |
|
|
Westlund Industries Fit All Saw Blades Ad Postcard 1970s $2.50 |
|
|
Edger blade 7-11/16 inch 1″ center hole fits many Echo / Stihl / Maruyama 6477 $2.50 |
|
|
2 Used EUROPEAN EURO ATC Blade Fuse Fits MERCEDES, BMW $2.60 |
|
|
2 Used EUROPEAN EURO ATC Blade Fuse Fits MERCEDES, BMW $2.60 |
|
|
2 Used EUROPEAN EURO ATC Blade Fuse Fits MERCEDES, BMW $2.60 |
|
|
2 Used EUROPEAN EURO ATC Blade Fuse Fits MERCEDES, BMW $2.60 |
|
|
2 Used EUROPEAN EURO ATC Blade Fuse Fits MERCEDES, BMW $2.60 |
|
|
2 Used EUROPEAN EURO ATC Blade Fuse Fits MERCEDES, BMW $2.60 |
|
|
Disposable Razor Buddy Blade Holder Fits Around Any Size Shaving Cream Can New $2.69 |
|
|
Refill Blades, Narrow Angle, Fits 2, 5, 6 EPIX202 $2.70 |
|
|
FREE SHIPPING Foil Fencing bayonet style socket will fit any foil blade CLOSEOUT $2.75 |
|
|
Nut to Hold Blades Star Shaft FITS CUB CADET MTD – NEW $2.79 |
|
|
FM34; 3Pc Scraper Oscillating Multi Tool Saw Blades Fits Fein Multimaster $2.83 |
|
|
Edger Blade 7 11/16″x2″ 1inch center hole Universal Fit $2.89 |
|
|
Aluminum Spinner 2″ Dia. for 2-Blade Prop Fits 1/4-28 Shaft Weights 2 Ounces! $2.99 |
|
|
New 12 Gillette Super Thin Double Edge Blade fit Parker $2.99 |
